When a pump fails, the process stops — water stops flowing, product stops moving and downtime costs start climbing. At WAT Engineering we rebuild what others replace. From small end-suction water pumps to large multistage, split-case and slurry pumps, our Muscat workshop restores worn and damaged pumps to OEM tolerances, tests them and returns them to reliable service across Oman.

WHAT WE DO
- Strip-down & failure analysis – full dismantling, dimensional checks and a photo-documented root-cause report
- Impeller repair & replacement – weld build-up, re-machining, vane profiling and dynamic balancing to ISO 1940 G2.5
- Casing & volute restoration – crack and erosion repair, re-machining of fits, ceramic-filled epoxy lining against wear and corrosion
- Shaft & sleeve repairs – straightening, metal-spray or weld build-up, new shafts and sleeves machined to drawing or sample
- Wear-ring & clearance restoration – new wear rings machined to bring internal clearances and efficiency back to design
- Mechanical seals & gland packing – single, double and cartridge seals, seal-face lapping and packing-to-seal conversions
- Bearings & housings – bearing replacement, housing-bore repair and lubrication upgrades
- Re-installation & alignment – laser shaft alignment, vibration and temperature checks at site start-up
PUMPS WE REPAIR
| Pump type | Typical applications | Faults we solve |
|---|---|---|
| Centrifugal end-suction (ANSI / ISO) | Water transfer, HVAC, process | Cavitation, impeller wear, seal leaks |
| Horizontal split-case | Water networks, cooling water, fire-fighting | Wear-ring loss, casing erosion, bearing failure |
| Multistage (horizontal & vertical) | Boiler feed, RO high-pressure, booster sets | Stage wear, balance-device damage, shaft run-out |
| Submersible & borehole | Wells, dewatering, sewage lifting | Seal failure, sand abrasion, motor burn-out |
| Vertical turbine & can pumps | Seawater intakes, cooling towers | Line-shaft bearing wear, column corrosion |
| Slurry pumps | Mining, crushing plants, cement | Liner and impeller erosion, gland leakage |
| Positive displacement (gear, screw, lobe, progressive cavity) | Fuel, oil, chemical dosing, sludge | Rotor/stator wear, loss of clearance and flow |
| API 610 process pumps | Oil & gas, refineries, petrochemicals | Seal and bearing failures, high vibration |
OUR REPAIR PROCESS
- Collection or site inspection – we collect the pump or inspect it in place
- Strip-down & inspection – measurements of every wear surface, with dye-penetrant or MPI testing where required
- Report & quotation – a clear repair-versus-replace recommendation before any work starts
- Repair & machining – in-house welding, machining and component manufacture
- Reassembly & balancing – rotating assembly balanced, clearances set and recorded
- Testing – hydrostatic pressure test and run test, with performance testing where specified
- Protective coating & dispatch – surface prepared and coated to suit the service environment
- Installation support – re-installation, alignment and commissioning on site
MATERIALS WE WORK WITH
Cast iron, ductile iron, bronze, nickel-aluminium bronze, stainless steel 304/316, duplex and super-duplex stainless steels. Replacement parts are matched to the original material — or upgraded where the failure analysis shows the original material was not suited to the duty, such as seawater, abrasive slurry or potable-water service.
WHY REPAIR INSTEAD OF REPLACE?
- Lower cost – a professional overhaul usually costs a fraction of a new pump
- Shorter lead time – days instead of months waiting for an imported replacement
- No re-engineering – the same footprint, piping and foundations, with no redesign at site
- Better than before – root-cause fixes and material upgrades extend the time between failures
- Sustainability – keeping existing castings in service avoids waste and embodied carbon
WHY WAT ENGINEERING
- Repair, machining, sandblasting and protective coating under one roof — see our sandblasting and protective coating services
- Pump-motor rewinding and repair through our motor repair team — one supplier for the complete pump set
- Emergency breakdown response for critical water, process and fire pumps
- Service across Oman, including Muscat, Sohar and Duqm
- Experienced on oil & gas, water utilities, desalination, cement, mining and building-services pumps
GET YOUR PUMP BACK IN SERVICE
Send us the pump nameplate details, a few photos and a short description of the problem at service@watengineering.com or through our contact page. Our engineers will respond with an inspection plan and a clear quotation.
Read more: Pump Types and Overhauling: How WAT Engineering Restores Industrial Pumps in Oman
